Podiums and lecterns · Cut, bonded and lit in our own factory

Acrylic Podiums Drawn Around the Person Who Speaks

Acrylic podiums are ordered for a conference opening, a graduation, a signing between two parties, an awards evening or a hall that hosts a speech every week. The order looks simple until the day itself: a speaker who cannot see the notes, a microphone cable hanging over the front, a logo lost in the glare of the screens. This page explains the height and the reading angle, the cables, the weight, the logo and how it reads on camera, so the lectern you order works for the speaker at it and for the photographs.

350+Projects behind us
15+Years in fabrication
10CNC machines in our own factory
24Hours to a detailed quote

What a Speaker Needs From a Lectern

Acrylic podiums are furniture for a few minutes of public speaking, watched by a full hall and recorded by cameras. These are what decide whether those minutes go well.

A top at the right height and angle

The reading surface sits a little below the elbow, sloped towards the speaker, so the eyes drop to the notes and lift back to the hall without the head bowing. A lip along the lower edge stops pages and a tablet from sliding off. When heights vary a lot, a low step behind the lectern serves the shorter speakers better than a top that is too high for everybody.

Room for what the speaker brings

Notes, a laptop with the slides, a clicker, a phone running a timer and a glass of water. The water belongs on a shelf under the top, never on the reading surface beside the papers. A laptop needs a flat area or a side wing, plus a port for the display cable, so nothing dangles over the front.

Cables that never cross the front

The microphone, the lit logo, a reading light and the laptop each bring a lead. Inside a well drawn podium they run down a channel at the back, gather at one exit near the floor and leave towards the rear of the stage, where the sound and power crews tape them down.

A body that stays still

A nervous speaker grips a lectern, and a relaxed one leans on it. The weight has to sit low, the base has to be wider than the top, and levelling feet take up an uneven stage deck. A clear podium that wobbles shows the wobble to every camera in the room.

Around the Podium: Work From the Same Teams

The lectern is one piece of a stage. These are made alongside it under one roof.

Printing & Promotional Gifts

A printed front for a podium that moves between events, the printed programme and gifts for the guests of honour. Graphics are printed in 1 to 5 working days.

Acrylic & Wood Fabrication

The wider service behind this page: lit letters, signs, display stands and award shields, cut on the CNC and laser machines that cut the podium.

Promoters & Brand Ambassadors

Hosts with a supervisor who walk each speaker to the lectern and keep water and notes ready before they go up.

Branding & Creative Studio

The logo prepared as a clean vector file that engraves and cuts well, in Arabic and in English.

Digital Solutions

Registration and attendance systems for the conference or ceremony where the podium stands.

Experiences & Events

The whole event around the stage, from the running order to the closing photograph.

Social Media & Content

Short clips and photographs of the speeches, ready to publish on the same day.

Custom Exhibition Stands

A stand with a small presentation corner and its own lectern, built and installed by the same team.

Kinds of Acrylic Podiums and What Each Suits

Each kind answers a different hall and a different kind of event. Many orders combine two of them.

A fully clear podium

Thick clear panels bonded into a single body, with polished edges that catch the light. It keeps the speaker visible from head to feet and lets the backdrop show through, which suits a light, modern stage. It also reveals everything behind it, so cables and papers need a plan.

Acrylic with a wooden body

A body in painted or veneered wood with an acrylic front panel and sometimes an acrylic top. It weighs more, hides the cables and shelves completely, and fits a formal hall, a ministry or a university council room where the furniture is already timber.

Acrylic on a metal frame

A slim frame in brushed or painted metal holding clear or frosted panels. The frame carries the load, so the acrylic can stay thinner and the lectern lighter to move, and the metal edge reads crisply on camera against a dark backdrop.

A podium with a lit logo

The logo is cut or engraved into the front and lit by LED from the edge or from behind, so it glows evenly in a darkened hall. It needs a power point near the stage and a dimmer, because a logo at full brightness turns into a white patch on video.

A slim lectern for short remarks

A single column or a pair of panels carrying a small top, for a welcome, a toast or a quick hand over lasting a few minutes. It takes little stage space and is easy to carry on and off, but it has no room for a laptop and will not take heavy leaning.

A presentation podium with shelves

A wider top that holds a laptop beside the notes, a microphone mount, a shelf for water and a closed rear compartment for a power strip and spare batteries. It suits a conference where every speaker brings slides and the lectern becomes a small workstation.

How Acrylic Podiums Are Ordered and Made

The order is quick to write. The details are where the real work is, and these are the stages in order.

1

The occasion and the hall

Tell us the event, the hall or stage, the backdrop colour, whether the podium stays put or travels, and who the speakers are. A signing, a graduation and a weekly lecture theatre each change the drawing.

2

A drawing with a person standing at it

The drawing shows a speaker at the lectern, the logo on the front, the microphone position and the cable exit, seen from the seats and from the camera position at the back of the hall. Height and reading angle are agreed here, not on the morning of the event.

3

Logo, material and light samples

Before production you see the logo method on an offcut of the same panel: engraved from behind, printed or raised. For a lit podium the sample is switched on, so the colour and strength of the light are approved in conditions close to the hall.

4

Cutting, bonding and polishing

Panels are cut on CNC and laser machines in our own factory, the joints are bonded, the edges polished, and wood or framing is added where the design calls for it. The protective film stays on every face until the last moment.

5

Assembled complete before it leaves

The podium is put together with its lighting and its spare front panels, checked for wobble, scratches and light leaking at the edges, then packed in its cover. What is found in the factory is not found on stage.

6

Placed and tried at the rehearsal

Our own team brings the podium to the stage, sets it level on its mark and stays while each speaker tries it at the rehearsal, so a height or a light can still be adjusted. After the event it comes back for storage or stays with you.

How Long Acrylic Podiums Take

A clear or printed podium

The date depends on the design, the panel and the logo method, and the quote states it.

A lit or framed podium

Lighting, wood and framing add stages, so the date depends on the finish you choose. The quote names the delivery day.

A new printed front

A printed front for an existing podium is printed in 1 to 5 working days once the artwork is approved.

Your quote

An itemised quote reaches you within 24 hours of the event details.

What Moves the Price of a Lectern

Acrylic podiums have no fixed price: each one is priced from its own drawing. The lines below are what moves the figure, so two offers can be set side by side and read fairly.

Panel and body

A body made entirely of thick clear acrylic uses more material, and finer bonding and polishing, than a wooden or framed body with an acrylic face. The visible joints of a clear podium are the slowest part to make well, because any bubble in a bond shows to the camera.

The frame

Wood adds joinery and paint, and metal adds a frame that carries the load. Either can reduce the acrylic needed, so a framed podium is not always the dearer one.

How the logo is made

A printed logo is the quickest. Engraving from behind, raised letters and a logo in two languages each add a stage, and a logo cut through the front with a second colour behind it takes the most work.

Light and power

A lit logo brings LEDs, a driver, a dimmer and a cable route inside the body. A reading light hidden under the lip of the top is a separate line.

Moving parts and spare fronts

Hidden wheels with brakes, a top that lifts off the base, a front that changes between events: each is a line, and each pays for itself when the podium travels or serves many organisations.

Cover, transport and storage

A padded cover or a rigid case, transport where it applies as a named line in the quote, and storage between events in our storage if you would like us to keep the podium for you.

Send the event, the hall, the logo file and a reference image if you have one. You receive an itemised quote for your podium within 24 hours. Request a quote or message 0567069088 on WhatsApp. When the lectern is for presentations on your own exhibition stand, our guide to exhibition stand cost in Saudi Arabia shows how that budget is built.

Where Acrylic Podiums Stand and What Each Occasion Asks

At a conference opening a new speaker steps up for every session, so the podium has to suit tall and short guests, carry a laptop with slides and look right on the live stream; the event as a whole is planned on our conference organisers in Saudi Arabia page. On any stage the lectern stands to one side of the backdrop, never in its centre, and its colour and logo follow the set described on event stages. At an awards evening the presenter and the honourees share the same photographs, which is why shields are often ordered together with the podium: see acrylic awards and plaques for the shields and employee award ceremonies for the evening itself. A graduation adds a long list of names read aloud and a patron who speaks first, covered on graduation ceremony organisers. When the podium is one piece of a complete identity across screens, signs and a photo wall, the brief belongs with event branding. A signing between two parties asks for something else again: a table with two chairs, a front panel carrying both logos, room for the two folders and the pens, and a podium beside it in the same material for the words before the signature.

Choosing the Right Lectern for Your Hall

There is no best podium, only the right one for a hall, a camera and a list of names. These questions settle most orders.

1

Will it stay in one hall or travel?

A podium that lives in a university theatre or a ministry hall can be heavy and fixed, with power brought up through the floor to its base. One that moves between hotels and venues is better split into a top and a base, rolling on hidden wheels, with a cover that goes everywhere it goes.

2

What is behind it, and what is filming it?

In front of a large LED screen, clear acrylic mirrors the screen and can vanish into it. A frosted front, a wooden body or a dark frame keeps the outline readable. If the event is streamed, ask for the front to be checked from the camera position.

3

Who will be speaking?

A list of speakers of very different heights needs a step or a top at a middle height. A speaker who sits, by choice or in a wheelchair, needs a table lectern or a lower podium with clear knee room, and that is decided before production, not after.

4

Lit or unlit?

A lit logo earns its place in a darkened hall and on an evening stage. In a bright daytime room it barely shows and adds a cable and a power point, so a carefully engraved or raised logo may serve you better.

5

Is there a signing as well?

For a signing, order the table and its front panel with the podium, in the same acrylic, frame and logo treatment, so the two pieces read as one set in the handshake photograph that will be published.

What Goes Wrong at the Lectern

Each of these happens in front of the whole hall, and each is prevented on the drawing before anything is cut.

Glare that hides the logo

Clear and glossy fronts mirror the stage lights and the screens, and on video the logo turns into a bright streak. A slight tilt of the front, a matt or frosted panel and a check from the camera position at the rehearsal solve it.

A lit logo that burns out or flickers

At full brightness an LED logo is the brightest thing in the frame, so the camera darkens the speaker's face to compensate. Some cheap drivers also flicker on video. Ask for a dimmer and a driver tested on camera; filming the lit sample with a phone shows the problem quickly.

A podium that rocks

A light body, a narrow base or a stage deck that is not level makes the lectern move when the speaker leans on it. Weight in the base, a footprint wider than the top and levelling feet keep it still.

A cable across the front

A microphone lead hanging over the front or a power cable crossing the stage spoils the photographs and trips people walking past. The route inside the body and the exit at the back are drawn before the first panel is cut.

A logo the microphone covers

A gooseneck microphone in front of the logo, or a logo placed so low that the front row hides it, wastes the most valuable part of the podium. The logo goes in the band the camera frames, clear of the microphone position.

Scratches and cracks from cleaning

Paper towels scratch acrylic, and cleaners containing alcohol or ammonia can leave fine hairline cracks. A soft cloth, water with a little mild soap and a cover between events keep a clear podium clear.

Made Where the Stage Is Made

With us acrylic podiums are drawn, cut on CNC and laser machines, bonded, joined to its wood, painted and lit under one roof, then placed on stage by our own team, so each follows the same files as the backdrop and the shields beside it. We have worked for the Heritage Commission, Saudia, Saudia Holidays, Kinan, Johnson & Johnson MedTech and Ascenda.

Conferences We Set Up

Conference halls and stages our team prepared for clients.

Ascenda stage set, by The Touch
Ascenda stage set
Ballroom conference with LED, by The Touch
Ballroom conference with LED
Conference hall with screens, by The Touch
Conference hall with screens
Ceremony seating with red carpet, by The Touch
Ceremony seating with red carpet
Ascenda conference in ballroom, by The Touch
Ascenda conference in ballroom

Questions About Acrylic Podiums

What organisers ask before they order a lectern.

What are acrylic podiums made of?

Clear or frosted acrylic panels, cut and bonded into a body, sometimes on a wooden or metal frame that carries the weight. The logo is engraved, printed or raised on the front, and it can be lit. Shelves, a microphone mount and a cable channel are part of the design from the start.

What height should a podium be?

That depends on who will use it. The reading top sits a little below the elbow of an average speaker and slopes towards them, and a low step behind the lectern helps a shorter speaker. Tell us who is on the programme and we draw the height around them.

Do you supply the microphone and the sound?

No. The microphone and the sound system come from the venue's technical team or from your own sound supplier. We build the podium around them: a mount or an opening for the microphone, and a channel that takes its cable to the back of the stage.

Can the podium carry a laptop?

Yes, if the top is drawn for it. A presentation podium has a flat area or a side wing for the laptop next to the notes, and a port for the display cable, so the speaker runs the slides from the lectern without help.

How is the logo put on the front?

Engraved by laser, often on the back face so it reads through the panel and cannot be scratched, printed in colour, or raised in cut acrylic letters. It can be in Arabic and English, and it can be edge lit or lit from behind.

Will a clear podium look good on camera?

It can, if reflections are planned. Clear acrylic mirrors screens and stage lights, so the front is tilted slightly, frosted, or set against a darker part of the backdrop, and a lit logo is dimmed until the speaker's face stays bright on video.

Is an acrylic podium heavy enough to be stable?

A clear body is lighter than wood, so the weight is placed in the base and the base is made wider than the top. Levelling feet take up an uneven stage. A wooden or metal frame adds weight where it is needed.

Can we move it between halls?

Yes. A travelling podium can split into a top and a base, roll on hidden wheels with brakes and go into a padded cover. Check the doors and service lift at each venue, do not leave it for long in a closed vehicle under the summer sun, and we can keep it in our storage between events.

Can one podium serve several events?

Yes, with a front that changes. The body stays, and a new engraved, printed or lit front carries the logo of the next event or the next partner. A new printed front is printed in 1 to 5 working days.

Where is it made, and how do we start?

We have more than one location in the Kingdom. Your podium is made in our own factory and placed by our own team. Send the event, the hall and your logo on WhatsApp at 0567069088 or through the quote page, and an itemised quote follows within 24 hours.

A Podium for Your Next Speech?

Send the event, the hall, the logo and the list of speakers if you have it. Within 24 hours you receive an itemised quote that names the material, the logo method, the light and the cover.

More specific pages on this

If your question is narrower than this page, these are written for one question each.

1
Powered by Joinchat
Call now WhatsApp